Forstner EASY
Fully rubberized pinch rollers
If you want to prepare your line for a film applicator, then the option with the fully rubberized rollers is ideal for you. This means that your line is ideally prepared for retrofitting a film applicator at any time and with ease.
S1 – Control
The SPS-S1 Control touch screen with intuitive features, that allow you to enter different quantities and lengths. The control uses the Electronic Eye to automatically set the zero point on square material. An optional radio remote can be purchased when adding later on a powered decoiler or recoiler, so the operator has everything under control.
The EASY series has 3 manual straightening rollers to remove coil set and give customers flat material every time. The rollers are made of polished steel with a 70 mm diameter. The pressure of the straightening rolls is set by locking handles with reference scale.
The Forstner EASY is the ultimate cut-to-length line for sheet metal processing in the construction industry. Set the lengths and quantities with the user-friendly control system. The sheet metal is fed into the machine and straightened and cut with fascinating precision. The cutting result is virtually burr-free with minimal waste.
The most important advantages:
- Small but extremely powerful.
- 3 roller manual straightener
- Intelligent and user-friendly user interface.
- High feed rates.
- Easy to operate machine.
| Specifications | |||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Machine | Type | Working width | Cutting capacity – Steel 400 N/mm² |
Cutting capacity – Stainless steel 600 N/mm² |
Cutting capacity – Aluminum 200 N/mm² |
Shear | |||||||||||||||||||||||||||||||||||||||||||
| mm | mm | mm | mm | ||||||||||||||||||||||||||||||||||||||||||||||
| EASY PRO 1250 | Cut to length | 1250 | 1,5 | 1,0 | 1,8 | Guillotine shear | |||||||||||||||||||||||||||||||||||||||||||
| EASY CUT 1250 | Cut to length | 1250 | 1,0 | 0,6 | 1,2 | Roller shear | |||||||||||||||||||||||||||||||||||||||||||
The EASY series has 3 manual straightening rollers to remove coil set and give customers flat material every time. The rollers are made of polished steel with a 70 mm diameter. The pressure of the straightening rolls is set by locking handles with reference scale.
The infeed guide roller are angled to match the loop of the coil from a decoiler. This helps prevent creasing on soft materials like copper, aluminum and zinc..
The table guide has four roller bearings (two on each side) to guide the metal in the pinch rolls. The roller bearings allow the metal to move easily forward and backwards without damaging the edges. This also keeps the material straight as the material is fed into the machine helping to ensure a square cut.
The SPS-S1 Control touch screen with intuitive features, that allow you to en-ter different quantities and lengths. The control uses the Electronic Eye to automatically set the zero point on square material. The control features a “material savings” mode which automatically stops the machine, raise the slitting knives automatically and then moves forward to cut the piece to length, while leaving a clean edge. An optional radio remote can be purchased when adding later on a powered decoiler or recoiler, so the operator has everything under control.
The film applicator can basically be mounted on any table. Using the deflection rollers and the fully rubberized feed rollers, the protective film is pressed on almost bubble and wrinkle-free. The device type F-AG z2mo has an additional arm with tension spring for tensioning the film during the return movement. This design is only applicable for single decoiling systems. Film applicator available in both 1250 and 1500 mm.
If you want to prepare your line for a film applicator, then the option with the fully rubberized rollers is ideal for you. This means that your line is ideally prepared for retrofitting a film applicator at any time and with ease. Fully rubberized pinch rollers available in both 1250 and 1500 mm.
Choose from a simple cradle up to motorized versions. Read more under respectively product.
The manual coilselector is a very cost-effective solution for quick and easy manual sheet metal changes. Up to eight coils are fixed in the manual coilselector. The desired sheet metal is manually pushed into the downstream machine via a handwheel.
Add a foot switch to your machine in the EASY series for external start of next order.
Do you often cut stainless steel sheets? Then your new machine should definitely be equipped with the higher-quality knives for stainless steel. The life of the blades is increased and you achieve perfect cuts over a long time. Ask your sales consultant if your application requires knives for stainless steel machining.
